LiCoO2中锂离子固相扩散系数随循环次数的变化

The solid diffusion coefficient of lithium-ion in LiCoO₂ cathode material has been investigated by the capacity intermittent titration technique (CITT) at different voltages and at different charge/discharge cycles. By SEM, XRD and FTIR techniques, the structure of LiCoO₂ was studied before and after charge-discharge cycles, and the relationship between solid diffusion coefficient and crystal structure was further discussed. CITT results show that the value of Li⁺ solid diffusion coefficient of LiCoO₂ is about 10^-12 cm²·s^-1. During the whole charge-discharge cycles, the Li⁺ solid diffusion coefficient decreased within the voltage of 4.0～4.3 V, which is attributed to the change of the structure of LiCoO₂.     

WS2 超细粉体的固相法合成

WS2 超细粉体的固相法合成;WS2;固相反应;过硫系数;高能球磨;粒度     

La传感器在测定铝液凝固过程中La活度研究

微量稀土加入铝或铝合金中，如果加入方法、数量、时间得当，可明显改善材料的多项性能．稀土对铝及铝合金的影响规律和作用机理，已取得了一些进展，但对稀土铝合金的热力学性质，尤其是溶解态稀土的研究少有报导［‘，2］．本工作采用L即．95C。。。。FZ。。多晶作为固体电解     

Chiralcel OD-RH手性柱拆分卡维地洛对映体

采用Ch iralcelOD-RH(纤维素3,5-二甲基苯基氨基甲酸酯)手性固定相高效液相色谱法研究了乙腈-高氯酸钠缓冲盐体系对卡维地洛的手性拆分情况,讨论了流动相的各个因素(有机相的种类和比例、缓冲盐浓度、酸度等)对手性拆分的影响。在乙腈-高氯酸钠缓冲盐(pH 5.5,50 mmol/L)的体积比为35∶65的色谱条件下,卡维地洛对映体获得了基线分离。     

Synthesis and structure of anhydrodimers of salicylaldehydes

Anhydrodimers have been synthesized by reactions of salicylaldehyde and 3,5-di-tert-butylsalicylaldehyde with SOCl₂ or PCl₅. A mechanism of condensation has been proposed, and the molecular structure of dibenzo-2,6,9-trioxabicyclo[3.3.1]nona-3,7-diene has been determined by X-ray structural analysis.Deceased.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 8, pp. 1549–1551, August, 1995.The work was supported by the Russian Foundation for Basic Research (Project No. 94-03-08653).     

核磁共振法测定高聚物的结构—核磁共振二维谱

介绍了核磁共振(NMR)波谱,尤其是核磁共振二维谱(2D NMR)在最近几年内的进展。内容包括怎样用NMR测定高聚物的序列分布、共聚物结构、聚合物的混溶性、聚合物液晶的取向度、分子量、短链度和长链支化度、凝聚态高聚物的多相结构等。     

Ni-SDC固体氧化物燃料电池阳极的合成和性质

采用柠檬酸-硝酸盐溶胶-凝胶低温自蔓延燃烧法制备氧化镍（NiO）粉末和Ce0.8Sm0.2O1.9（SDC）粉末，并将NiO与SDC按不同质量比和不同制备工艺制备了固体氧化物燃料电池（SOFC）的阳极前身。再用自组装的还原装置将其在820℃经2．5h还原后，采用四端子法测量其电导率值。分析了阳极片电导率与阳极片微结构、Ni的质量百分数、混合研磨时间及烧结温度之间的关系。结果显示，阳极片的电导率强烈依赖于镍含量和制备工艺。     

Synthesis and Structure of Ag_3PSe_4

The title compound Ag3PSe4 was synthesized by the reaction of Ag powder,P2Se5 and Se in a molar ratio of 1:1:1 at 500℃ and structurally characterized by X-ray crystallography.The crystal belongs to orthorhombic,space group Pmn21 with cell parameters:a=7.689(4),b=6.660(3),c=6.379(4)A,V=326.7(3)A^3,Z=2,Dc=6.816g/cm^3,Mr=670.42,F(000)=584,μ=31.302mm^-1,R=0.0606,wR=0.1289 and S=1.012,The 3-D structure can be regarded as constructed from the stacking of puckered Ag-P-Se honeycomb-like sheets along the c direction,in which the Ag,P and Se atoms are bonded to each other to form a chair-like six-membered ring,and the rings then build the sheets by sharing edges.     

Influence of thermal and thermo-mechanical treatment

Two lipids with similar melting ranges but of different composition were analyzed using differential scanning calorimetry and X-ray diffraction. The lipids were processed via extrusion or were tempered at different temperatures; they were analyzed directly after extrusion and after storage at 40°C. Precirol ATO 5® showed high sensitivity to storage time and varied temperature exposure. Extrusion showed only marginal influences on the solid state. Melting peaks were narrower and shifted to higher temperatures in comparison to the untreated powder. Dynasan 114® was more robust, changes in the solid state could only be shown for samples treated above the melting range. Thus, Dynasan 114® is more appropriate for solid lipid extrusion of pharmaceutical products.